Apr 22, 2015 According to Conlog, the BEC23 meter has reverse energy detection and disconnection. I have logged a call with Conlog to find out if there is any indication of this disconnection on the meter itself. I do not see anything. What I can confirm is that the meter is off for 50 seconds, on for 15 seconds and so it repeats. SANS 1524-1:2018: Meters-Prepaid; SANS 1799:2015: Meters- Post Paid; ISO 9001: 2015: Quality Management System; IS0 45001: 2018: Health & Safety Management Systems. Hacking Conlog Prepaid Meters Download Film Anime Jepang Subtitle Indonesia Oh Monster Hunter Iso For Ppsspp Gold Windows XP Pro SP3 Ultra Lite ITA Gilli Eng Sub Kindly Refer To The Attached File For Your Perusal Script Of Malayalam Movie Pdf Left Right Left Malayalam Movie Mp3 Songs 320kbps. Jan 31, 2011 TO hack an electricty meter first look at the meter tails uk size is 16mmsq. The phases usully run in this order- phase, rtn, rtn, phase. The last part RTN, PHASE goes to fuse pannel. ITS the first part on the left thats wanted, PHASE, RTN. But by putting this size cable in is DANGEROUS!!! It is however the only size that will fit.
As the use of prepaid meter is gradually taking over the electricity industry, so also is the rise in trouble using the prepaid meter device.
This article gives a detailed explanation of how to load a token on CONLOG PREPAID METER and how to rectify a mistake.
It was born out of a personal experience dated 08/12/2020. My brother was asked to load the prepaid meter of the church and he called me to give him directives on how to go about it and I told him.
I don’t know how to do it except if I search around on Google which I did and found nothing.
Hacking Conlog Prepaid Meters Amazon
Unfortunately, he tried the directive of the Pastor and it caused an error that reverted a message that said “please register the meter”.
The vendor of the Prepaid token was contacted and the rectification process was initiated which I will explain later in the article.
Note: you can not load your prepaid token when there is no power i.e when “Re con” is on the display.
Steps to load your purchased prepaid meter token.
- Input the 11 digit meter number and wait for some seconds
- Input the 20 digit token to activate your prepaid meter (just input the 20digit and wait).
My brother thought since there was no visible enter button so # must be the enter button and that caused the machine to send back error code.
Follow the following step to rectify the error if you ever make the same mistake - On request, your vendor will send 20digits code in two places.
- Input the 11 digit meter number
- Input the first 20 digit
- Input the second 20 digit and you should see “DONE” displayed which implies that the error has been rubbed off.
After this step, you can go back to the first step and your prepaid meter will be activated.
With the privatization of the power sector a few years ago, there have been some changes in the sector, one of which was the introduction of the prepaid meters.
These meters enable customers to regulate their electronic energy consumption and recharge whenever the energy is used up.
There are several ways to recharge your prepaid electric meter if you have one. But first, you should have a smart card which you can use to purchase, load, retrieve or sell power credit.
Prepaid meter codes for recharging and checking balance
The first step is to configure your smart card at any of the disco outlets close to you.
After the configuration, you can then use your smart card to recharge your electronic energy prepayment unit.
Usually, energy credit is recharged with a 20-digit pin code. Below are the six simple steps to recharge your meter and the codes you need to input
- Go to any dealer outlets or disco offices close to you with your smart card.
- Present them with your card which carries your meter number
- Request for the credits you can afford
- Your account will be credited by the agent and you would be given a slip containing a 20 digit code along with your receipt.
- When you get home, enter the 20 digit code through the UIU Keyboard. Observe the UIU LCD screen as you type to ensure you’re entering the correct digits
- If the token you have entered is correct, the screen will show “ACCEPT” which means that the recharge is successful. However, if the screen displays “REJECT”, this means the code isn’t accepted and the recharge FAILED. A “REJECT” sign may mean that you have entered a wrong or invalid recharge code.
Apart from the 20 digit code, you can also recharge with your smart card. Here’s how to do it.
Once you get home, open the card door of your monitor unit and insert your smart card in the proper direction indicated on card. You need to ensure that the control box is connected to a power source. You will see the LCD screen of the monitor unit displaying a symbol like this “——“. This means that your meter and card are communicating (credit loading is incomplete). At the end of the process, the updated credit level of your meter will be displayed on the LCD once loading is complete.
Hacking Conlog Prepaid Meters Free
You should NEVER remove the smart card while loading is incomplete. This can damage your smartcard, meter, or both.
Here are the things to check once loading is complete.
- Meter number
- Balance
- Total credit used
If you don’t know how to check your meter number, press 65 then the blue button, the meter number is the 11 digit numbers that displays on the screen.
If you want to check your balance, you can press “07” on the keypad and then press the blue button. The available balance will be displayed in this format. (102.12).
Also, to check the total credit used, press 07 on the keypad then the blue button, then wait for the reply to be displayed as shown above.
![Prepaid Prepaid](/uploads/1/3/4/2/134214653/743124070.jpg)